Plus Touch
Model: PLUS-TOUCH
Plus Touch
Model: PLUS-TOUCH
Introducing the Plus Touch Series — The PEC Plus redesigned
Plus Touch brings a wealth of new features that make it more powerful and more versatile.
View comparison chart
More than just temperature
Plus Touch can monitor humidity, ammonia, carbon dioxide, and more. It can then use those conditions to influence how it controls equipment. For example, if the humidity is too high, it can switch heaters on or increase ventilation to reduce it.
VentGridâ„¢ merged ventilation
In addition to traditional staged control, Plus Touch offers VentGrid merged ventilation. Merged mode has up to four steps. The benefit is that merged mode can provide smoother transitions between steps than traditional staged mode can between stages.
Growth and minimum ventilation curves
Growth and ventilation curves are powerful features that allow you to automatically change the temperature set point and minimum ventilation rate over time to adjust to requirements as your animals grow.
Completely programmable in the little as 5 minutes
That’s a bold statement, but Plus Touch is more than a new look and name; it is a completely new user experience. The buttons and LED display have been replaced with a 5-inch touchscreen that allows you to more easily configure, program, and monitor your room and equipment.
Backwards compatible
Plus Touch is backwards compatible with all earlier PEC Plus control (bottom) boards. To upgrade to a Plus Touch and add all the new features, you purchase a display upgrade kit, connect it to your existing PEC Plus control board, and then program your new control.
| Programming options |
| Temperature-based control |
|
|
| Control zones |
2 |
|
| Staged ventilation mode |
|
|
| VentGridâ„¢ mode |
|
|
| Manual override mode |
|
|
| Growth curves |
2 |
|
| Minimum ventilation curves |
2 |
|
| Secondary modifiers |
|
|
| Relay stagger |
|
|
| Hysteresis |
|
|
| Sensor inputs |
| Phason 3K Series |
5 |
|
| Outdoor temperature |
|
|
| DOL 114 |
|
|
| DOL 119 |
|
|
| DOL 53 |
|
|
| Stages and relays |
| Variable AC stages |
2 |
|
| 0 to 10 V DC signal outputs |
4 |
|
| General-purpose relays |
6 |
|
| Alarm relay |
|
|
| Variable and relay configuration |
| Variable cooling and heating |
|
|
| Relay cooling and heating |
|
|
| Duty cycle |
|
|
| Actuator / inlet |
|
|
| Curtain machine / winch |
|
|
| Misting/sprinling/fogging |
|
|
| Timed events |
|
|
| VFD control |
|
|
| Other |
| 5-inch touchscreen |
|
|
| Scrolling status screen |
|
|
| Updatable firmware |
|
|
| Transferable settings |
|
|
| Diagnostic |
|
|
| Hourly and daily logs |
|
|
| NEMA 4X enclosure |
|
|
| CSA approval |
|
|
| CE certification |
|
|
| 2-year warranty |
|
|
- Incoming power
120/230 VAC, 50/60 Hz
- Variable AC stages
10 A at 120/230 VAC, general-purpose (resistive)
7 FLA at 120/230 VAC, PSC motor
1/2 HP at 120 VAC, 1 HP at 230 VAC, PSC motor
- Variable AC stage fuses
15 A, 250 VAC ABC-type ceramic
- Variable DC stages (optional)
0 to 10 VDC, 2K Ω load
- Relay stages
10 A at 120/230 VAC, general-purpose (resistive)
1/3 HP at 120 VAC, 1/2 HP at 230 VAC
360 W tungsten at 120 VAC
- Alarm relay
0.4 A at 125 VAC, 2.0 A at 30 VDC, resistive load
0.2 A at 125 VAC, 1.0 A at 30 VDC, inductive load
Manual Override Box
The Manual Override Box increases the load handling capability of your control's relays and provides an external disconnect.
View Product
Variable DC Module
The Variable DC Module has four 0 to 10 V DC signal outputs.
View Product
FanDRIVE (2x7 FLA)
FanDRIVEs expand the capacity of your control system by taking the 0 to 10 VDC signal from the control and adjusting fan speed.
View Product
FanDRIVE (1x14 FLA)
FanDRIVEs expand the capacity of your control system by taking the 0 to 10 VDC signal from the control and adjusting fan speed.
View Product
Temperature Sensors
Additional temperature sensors allow you to use 4-zone temperature averaging. Probes are available several lengths and can be extended up to 500 feet using extension cable.
View Product
DOL16 Light Sensor
The DOL16 measures light intensity in two different ranges: 0 to 100 and 0 to 1000 lux.
View Product
DOL53 Ammonia (NH3) Sensor
The DOL 53 is designed for stationery, continuous monitoring of ammonia (NH3) in livestock and industrial facilities.
View Product
DOL114 Temperature and Humidity Sensor
The DOL 114 is a high-precision temperature and relative humidity sensor available in 4 to 20 mA, 0 to 3 V, 0 to 5 V, and 0 to 10 V versions.
View Product
DOL119 CO2 Sensor
The DOL 119 measures carbon dioxide (CO2) in a range that has been selected to care for animal comfort and monitor error conditions.
View Product
Upgrade Kit | Convert PEC-PLUS-RS to PLUS-TOUCH
View Product
General
Can the PLUS TOUCH control a misting system?
Yes. The Plus Touch has two zones and six relays It can support two independent misting systems with a total of six control elements. Set them up as a temperature-controlled duty cycles.
Can I control a pump by humidity?
Yes. The Plus Touch controls equipment using temperature as a primary control mode. However, if you set up a cooling relay with a very high temperature set point, it should never turn on from temperature. Then, you can set up secondary modifiers for that relay to switch the pump on and off based on humidity readings. Note that this will require a humidity sensor.
Can I control equipment that requires a 0 to 10 V DC-signal input?
Yes. You can easily connect a VDC-4 (Variable DC Module), which gives you four 0 to10 V DC-signal outputs that you can use to control variable heating and cooling equipment.
Do I need the KPT-DISPLAY or the KPEC-PLUS TOUCH?
The KPEC-PLUS TOUCH kit is for upgrading a PEC-PLUS-RS to a Plus Touch. The KPT-DISPLAY kit is for replacing a damaged display on a Plus Touch.
PEC-PLUS-RS control boards have a large black heatsink (seen here). These require the KPEC-PLUS TOUCH kit. Plus Touch control boards have a small power supply (seen here) instead of the large heatsink. These require the KPT-DISPLAY kit.
How big is the control?
The enclosure is 9 x 7 x 3.75 inches (23 x 18 x 9.5 cm). The heatsink adds an additional 1.25 inches (3.5 cm) to the width.
Installation
How do I set up modifiers?
Modifiers can be found in the menu under Settings. For a complete walkthrough of modifiers, see Programming modifiers in the Plus Touch user manual.
How do I set up a VentGrid (merged ventilation)?
VentGrid splits your ventilation into steps to help create smoother transitions as ventilation increases. For a full walkthrough of programming VentGrid, see Programming merged ventilation in the Plus Touch user manual.
How do I calibrate actuators?
Calibrate actuators by pressing their widget on the home screen and then pressing Calibrate, or by going to their equipment configuration page and pressing Calibrate Actuator.
How do follower relays work?
A follower relay mirrors the stage of the output that it is following. If it is following a relay, then it is on when the other relay is on, and off when it is off. If it is following a variable output, then it is off when the variable output is at 0 percent, and on when it is between 1 and 100 percent.
Troubleshooting
Why is my variable AC fan not turning on?
How do I reset the control to its factory defaults?
Go to the Administration menu and then press Restore Defaults. For more information, see Restoring the factory defaults in the Plus Touch user manual.
How do I save and restore settings?
Insert a USB into the control, go to the Administration menu, and then select either Save Settings or Restore Settings. For more information, see Saving and restoring settings in the Plus Touch user manual.
Why does my variable AC fan perform poorly and have a small operating range?
Some fans motors work better with different fan curves. The Plus Touch has four fan curves to choose from. Go to the configuration screen for the applicable variable stage and then try the other fan curves to find out which one performs the best. For more information, see Appendix F: Motor curves in the Plus Touch user manual.
Web Services Login
